Wait about two minutes after rebooting the router and then reconnect the Seagate NAS' Ethernet and power cables. Once it's completely disconnected, turn off your computer, and then reboot your router. Steps to power cycle your network are below:įirst, unplug the Seagate NAS from power, and then from the router by unplugging the Ethernet cable. If nothing on your network sees the NAS at all, then you should power cycle your network. If you still cannot access the NAS, check to see if another device (computer, TV, or Media Player) on your network can see it. Make sure you are not connected to a guest network. Here is an example of how it should be hooked up: Your NAS is plugged into your router via Ethernet cable and your computer is connected via Ethernet or Wi-Fi to that router. Make sure the computer is connected to the same network as the NAS. Here are a few suggestions for what to try next: If you still can’t connect to the NAS, then your computer might not be connected to the correct network. This will allow the NAS to show up on your Desktop. Under the General tab make sure “ Connected servers” is checked. If you do not see the NAS there, follow these steps:Ĭlick on Finder in the top left hand corner of your screen. If you do not see the NAS in Finder, check your desktop. Change this to the username of the account on the NAS you would like to access the NAS with. Note: By default, your Mac will auto-populate the username field with the Mac's username. The drive is now mapped and can be accessed under Finder > Shared When prompted, enter your username and password and select Connect. Note: Make sure you use a forward slash (/) and not a backslash (\). ![]() ![]() In the ‘ Connect to Server’ window, type: cifs://IP Address or afp://IP Address (ex. Now that you have the IP address of the drive, make sure that you see Finder in the top left corner of your screen, then click on Go, then Connect to Server. Once you have located the MAC address, look to the right and make note of the IP address associated with the MAC address. All Seagate NAS units start with 00:10:75, however terminal will only display the first zero. Note: You can find the MAC address on the bottom, or backside of your Seagate NAS. Locate the Seagate NAS MAC address in the list. You will see a list of IP and MAC addresses. Make sure you see ‘Finder’ in the top left corner of your screen (by clicking the desktop first) then click on Go, then Utilities. (Only applies to Seagate NAS Pro 4 and 6-bay models) - If you find the IP address with this method, or already know the IP address, skip to step 6 below. See this section of the Seagate NAS Pro user manual for more information. Note: On Seagate NAS Pro models with the LCD monitoring screen on the front, you can find its assigned IP address there instead of looking in the Arp table from Terminal (as described in the steps below). Below are instructions for connecting to a NAS from Mac OSX using a different method: Graphically, it is very intuitive, and scanning the local network is done instantly, without having to wait at all.You may be experiencing an issue after updating to El Capitan (Mac OS 10.11) when trying to view your NAS in Finder: it shows up as a question mark, or it just gives an error message when trying to connect to it. Note: QNAP Qfinder Pro is a highly advanced program, even compared to Synology Assistant. Follow the instructions in the image below. For example, you can select your QNAP NAS device, then, at the top left of the page, click the Login icon.Īfter you click the Login icon at STEP 2, your browser will automatically open the page with the link for the selected device. The Qfinder Pro will automatically scan and find all your QNAP devices on your local area network. ![]() In today’s article I will show you how to use Qfinder Pro to find your QNAP NAS in your local network.ĭownload the latest Qfinder Pro software for your computer from the blue link below.Īfter the Qfinder Pro is installed on your computer, launch it. Qfinder Pro is available for Windows, Mac and Ubuntu 32/64 bit. Once you install the Qfinder Pro, you will see the latest installed OS version, local IP address, MAC address as well as the name of your QNAP device all at a glance. What the Qfinder Pro does is help you automatically find the address of any QNAP device in your local area network. If you are a QNAP user, whether you have a NAS, a router or a QNAP switch, then one of the best pieces of software you’ll use is the Qfinder Pro.
0 Comments
Leave a Reply. |